How Exactly To Install A Fishfinder. Steps: Installing The Binnacle Mount

How Exactly To Install A Fishfinder. Steps: Installing The Binnacle Mount

Take about this easy electronics installation, and you will see just what lies beneath your motorboat.

Whether you are a diehard angler, a laid-back fisherman, or even a week-end cruiser, you almost certainly have or wish to have a fishfinder onboard, so installing or changing a fishfinder is just a task you’ll likely tackle eventually. Fortunate for people, with regards to binnacle-mounted units which use transom-mounted transducers the most typical fishfinder installments from the water this might be an simple DIY work you can easily handle. All you have to are a definite few tools and the knowledge, that you can find the following on these pages.

Step One: Installing The Binnacle Mount

Before starting this mounting task, you will need to discover the location that is best. Attempt to keep consitently the fishfinder because close as you possibly can to focus on the helm, which supplies the most useful watching angle. The system must be between waist- and shoulder-high; steer clear of overhead locations that are mounting like in an electronics package or hanging down from the hard-top, that may force you to definitely crane your mind right back with all the product that will induce throat strain. Additionally, verify the location enables you to tilt and/or turn the machine without striking the windshield, throttle, compass, or any other affixed things.

Inspect the helm place through the back or underside, to guarantee the area underneath is obvious of obstructions, and it has enough space for protruding bolts and cables. This is certainly also a good time for you to find the power bus and/or fuse block, and also make certain you’ve got terminals designed for usage; ABYC specifications provide for as much as four terminals per stud. When you have opted for the positioning, either utilize the binnacle template incorporated with the fishfinder, or make use of the binnacle itself as a template, to mark the area for the holes that are mounting a pencil. Drill out of the mounting holes along with your energy drill, operating it at complete rate all of the time (a gradually switching drill bit is very likely to get the gelcoat’s sides, causing it to splinter and chip).

Now you’ll need an entry/exit point for the product’s wires. If your wanting to drill one out, inspect the system to be sure there is not currently a gap from the previous gear installation, which you yourself can re-use the less holes in your helm, the greater. Presuming you do not log off really easy, you shall want to drill an opening directly behind the binnacle mount. Be sure it’s big enough to accept all the device’s cables, and if your wanting to drill, place the binnacle and fishfinder temporarily in position to make certain there is enough approval between your mount additionally the opening for the cables to feed, without making any razor-sharp bends. Otherwise, the cables might rub from the side of the opening and chafing may become a nagging issue in the future.

First things first: discover the most readily useful location for the fishfinder.

Step Two: Operating The Ability Leads

With respect to the amount of the provided cables, you could or might not need certainly to lengthen or reduce the power leads. If you wish to lengthen them, make sure to stick to the appropriate color-coding and tinned-copper wire (motorboat cable) associated with maker’s suggested measure. Wire-to-wire connections must certanly be fashioned with crimped barrel connectors never solder and really should be protected by heat-shrink tubing. And anything you do, do not cut the manufacturer out’s included in-line fuse remove it and you also might fry the machine, along with invalidating the guarantee.

Drive the power leads straight straight down through the exit gap you drilled, through to the plug has sufficient freedom to achieve the machine without additional wiring exposed outside the helm. Then run the cable to your helm’s fuse block. Secure the cables every 18 ins with tie-wraps or cushioned clamps, which makes certain to minimize droops and slack. In case the fuse block has spade that is male, crimp feminine spade connectors into the ends associated with energy leads and protect the connections with heat-shrink tubing. If this has screw-type terminals, usage band connectors regarding the size that is appropriate. Leave the ends that are terminal, while you finish the installation.

Step Three: Mounting The Transducer

Finding the right location is crucial before you begin the real installation. Stay behind the transom to check out a location as deep regarding the hull that you can, without any strakes, through-hull fixtures, or any other products interrupting the smooth hull in front side from it. Something that disturbs water movement shall produce turbulence, which degrades the fishfinder’s performance.

Whenever you’ve discovered the spot that is best, support the transducer bracket up against the transom and adjust its place until it holds the facial skin for the transducer completely horizontal and about 1/8-inch underneath the operating area for the hull. Employing a pencil, mark the place for the bracket’s mounting holes. Just before actually mount the transducer, nonetheless, now’s the right time and energy to run the transducer’s cable towards the dash. (do this after the mounting procedure, and you also might destroy the sealant’s hold by inadvertently jerking regarding the wire). The old wire to draw the new one through the wiring chase if your boat had an old fishfinder with a transom mount transducer, cut the transducer off the end and use. If you don’t, you will need to start from scratch using a cable seafood to pull the transducer that is new and plug through.

When you have drawn every one of the cable to your helm and routed it through the opening you have made, coil any line that is extra the helm, and secure it with tie-wraps or cushioned clamps. WARNING: never ever slice the transducer cable down seriously to size; this new connections you need to make during the plug can make resistance that is additional the cables, therefore the fishfinder’s performance are affected. 2ND WARNING: do not bundle the transducer cable using the motor’s wiring harness or VHF cable; they could cause electric interference that will degrade the machine’s performance.

Making use of the markings you made early in the day in the transom, drill pilot holes for the bracket’s mounting screws along with your energy drill. Then utilize 3M 5200 adhesive/sealant to coat the mounting liberally screws plus the holes within the transom. While keeping the bracket in position, screw into the mount. Utilize plenty of that adhesive/sealant. The thing that is last want are holes in your transom that let water immerse through.

The end result should be more fish caught if you follow these steps.

Step Four: Finishing The Task

Have minute to safeguard the cables within your helm by sealing from the wiring gap you made behind the binnacle mount. Make use of a grommet to seal it when possible (silicon sealant works, if you fail to get yourself a grommet that fits), then protect it having a clamshell vent; simply support the clamshell in position within the gap, mark the spots you’ll need to drill, and screw it down. Now you’re prepared to finish your last wiring connections. After making certain the battery pack is powered down, link the charged energy leads, then plug the ability and transducer cables to the straight back regarding the fishfinder.

Now, hold a sec on. Before you splash the ship for a test run, make certain the 5200 you utilized to seal the transducer mounting holes has received an abundance of time and energy to dry. This can take up to a full week, so don’t rush it in some conditions. You have to be 100-percent water that is sure will not occur.

When you introduce the watercraft and idle far from the dock, the fishfinder shall almost truly work fine. But issues usually arise with transom-mounted transducers when you strike the throttle and acquire onto air air plane. In the event your product loses the reading totally, the transducer might be too high (in a few full situations, it could drive totally from the water). If the bottom reading is periodic, it’s likely that it’s simply a locks too much, or it could be low sufficient that it is producing turbulence. Luckily for us, almost all transducer brackets enable some available space for modification. Decide to try bringing down or increasing the transducer in 1/8-inch increments, until such time you discover the most readily useful height. But understand that few transom mounts work very well at quite high rates. If you’re able to achieve 30 mph or even more, whilst still being keep an excellent reading, you have done a job that is great.

Every thing’s working perfectly? Exemplary work. Now trade in those tools for the pole plus some bait, and discover just just just how that brand new fishfinder will allow you to fill the cooler. So when you are done, obtain a waterproof address to guard that brand new product. Many covers given by the producer only protect the LCD display, however an address that slides on the fishfinder that is entire do a more satisfactory job. Р’

Leave a Comment!

Your email address will not be published. Required fields are marked *